AUX E&H Series Betriebsanleitung Seite 26
- Seite / 92
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Factory settings
When the instrument is switched on for the first time, the factory settings are in effect. The
following table provides an overview of all major settings. Please refer to the description of the
individual functions in chapter 5 for all other factory settings (the factory settings are printed in
bold face).
Alarm contact
Normal operating state:
• Instrument in operation
• No error message available
(Alarm LED off)
→ Relay picked up
→ Contact 42/43 closed
Alarm state:
• Error message available (Alarm LED red)
or
• Instrument defective or voltage-free
(Alarm LED off)
→ Relay dropped out
→ Contact 41/42 closed
Function Factory setting
Mode of measurement
pH or Redox absolute, Temperature in °C
Type of temperature compensation
linear with reference temperature 25.0 °C
Temperature compensation
automatic (ATC on)
Limit value for controller 1
pH 16 (redox: –1500 mV or 0 %)
Limit value for controller 2
pH 16 (redox: +1500 mV or 100 %)
Hold
active during configuration and calibration
Contact 1 / 3
pH limit contactor, function off
Contact 2 / 4
pH limit contactor, function off
Current outputs 1 and 2*
4 ... 20 mA
Current output 1: measured value
for 4 mA signal current
pH 2
Current output 1: measured value
for 20 mA signal current
pH 12
Current output 2: temperature
value for 4 mA signal current*
0.0 °C
Current output 2: temperature
value for 20 mA signal current*
100.0 °C
* equipped accordingly
RELAY2.CDR
Normal operating state
Alarm state
41
42
43
41
42
43
Fig. 5.3
Recommended fail-safe
circuit for an alarm contact
Instrument configuration Liquisys M CPM 223 / 253
24 Endress+Hauser
- Endress Hauser 1
- Table of contents 3
- 1 General information 4
- 1.5 Product structure 5
- 2 Safety 6
- 2.5 Immunity to interference 7
- 2.6 Declaration of conformity 7
- 3 Installation 8
- 3.2 Dimensions 9
- 3.3 Mounting 10
- PM253E03.CHP 11
- 3.3.2 Mounting examples 12
- Endress+Hauser 11 13
- 3.4 Electrical connection 14
- 131094-4G 15
- Construction of special 16
- CPK1_12e.EPS 16
- Fig. 3.13 16
- • If the software setting 18
- Setpoint 19
- 4.3 Keys 20
- PM253ED4.CHP 21
- 4.5 Operating concept 22
- 4.5.2 Access codes 23
- 4.5.3 Menu structure 23
- • If a change is made but not 23
- • See the appendix of these 23
- 5 Instrument configuration 25
- RELAY2.CDR 26
- Oper.Mode 27
- Glass A5 28
- Fig. 5.4 29
- Alarm signalling and 29
- 28 Endress+Hauser 30
- PM253E5A.CHP 31
- Fig. 5.7 32
- User-defined current output 32
- Sel. Out2 33
- Tabelle (3) 34
- Table (3) 34
- 5.5 Monitoring functions 35
- Rel.Assg 36
- Curr.Assg 36
- CleanTrig 36
- 5.5.2 Check 37
- • Due to its semiconductor 37
- A.Thresh 38
- Err.Delay 38
- LowAlarm 38
- HighAlarm 39
- ProcMonit 39
- Tmax Low 39
- Tmax High 39
- GRENZ-E.CDR 40
- not allowed 41
- Pulse length modulation 42
- Pulse frequency modulation 42
- PM253E5B.CHP 43
- 5.6.4 ChemoClean function 44
- • Use relays 3 (water) and 44
- • When “Economy” is selected 44
- LC PV R2 45
- LC State 46
- 120 R239 48
- 0.3 R2310 48
- Clean = ChemoClean (5) 49
- Neutra controller (6) 49
- ChemoClean (5) 49
- Proc.Type 51
- 5.7 Service 52
- S.Default 53
- Contr E1 54
- SerNo E113 54
- LSG E114 54
- 5.10 Calibration 55
- the user is 55
- ≤ 0.05 and value 56
- 59.18 N2 59
- PV Offset 60
- 6 Interfaces 61
- Endress+Hauser 61 63
- 62 Endress+Hauser 64
- Endress+Hauser 63 65
- 64 Endress+Hauser 66
- Endress+Hauser 65 67
- 8.1 Diagnosis 68
- Endress+Hauser 67 69
- 223EXPHE.CDR 70
- 8.2.2 Disassembly of CPM 223 71
- 8.2.3 Assembly of CPM 223 71
- 8.2.4 Spare parts for CPM 223 72
- 253EXPHE.CDR 73
- 8.3.2 Disassembly of CPM 253 74
- 8.3.3 Assembly of CPM 253 74
- 8.3.4 Spare parts for CPM 253 75
- 8.4 Spare parts orders 76
- 8.6.1 pH/redox transmitter 77
- 8.6.2 pH/mV electrodes 77
- 8.6.3 Assembly 77
- 8.6.4 Liquid KCl supply 77
- 9 Accessories 79
- 10 Technical data 81
- 80 Endress+Hauser 82
- Endress+Hauser 81 83
- 11 Appendix 84
- Endress+Hauser 83 85
- 84 Endress+Hauser 86
- Endress+Hauser 85 87
- 12 Index 88
- PM253E12.CHP 89
- Declaration of contamination 91
- BA 194C/07/en/07.02 92
- Printed in Germany / CV5 / DT 92
Verwandte Produkte und Handbücher für Split-System-Klimaanlagen AUX E&H Series
(15 Seiten)
(19 Seiten)
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern